Internet Computer Mobile Games

How to configure 2 LAN as input and one output ports in juniper switch

Top similar posts to How to configure 2 LAN as input and one output ports in juniper switch

configure Cisco switch with tagged VLAN packets

My Netgear smart switch died and was replaced with a Cisco Catalyst 2960-S managed switch. Using Cisco Network Assistant or the web interface how do I add a VLAN with ID "2", put port 46 on VLAN ID 2 and make port 47 handle packets tagged as ID 1 and ID 2 and route them accordingly (packets tagged as ID 2 goes to port 46, tagged as ID 1 goes to everything else)? P.S. - In case this is useful... basically I have a private/corporate network and a public/guest network setup each with their own WAN...

how to configure aruba switch to use the stacking interfaces fiber uplinks t...

We have several small locations with 3 and 4 IDF's and would like to use the 10 gig interfaces or stacking interfaces on Aruba switch for fiber uplinks to other aruba switches. how do we configure the stacking interfaces for this? Read More...

P0704 -Any Help on Diagnose (Cluth Switch Input Circuit Malfunction)

Hi MDxers, Just yesterday my 2004 MDX throw P0704 code (A?T System Malfunction) with the D5 blinking, VSA light flashing and the check engine on. P0704 seems to be a transmission problem but I don't understand while the check engine has to come up as well. Edited again, the code is P0700 Recent History of Issues and Troubleshooting Like three months ago the SUV start jerking when you shift from P-D5, D5-R, R-N, D5-P etc. the point is, it jerk in all direction, some times noticeable and som...

Trying to setup a port channel to connect a new switch with ports that were previously configured.. error

I'm trying to add a 2 interface port channel, nothing fancy, but i keep getting errors due to the switch already being configured as a switch port on a non-default vlan. when i issue command "no switchport" on either of the 2 interfaces i get this error...

Trying to setup a port channel to connect a new switch with ports that were previously configured.. error

i removed the ports from vlan 2 with "no untagged gigabitethernet 2/36" and on 37 but when i try and run no switchport Error: Port has Layer-2 config on it Gi 2/36. different error. when i try and add it to the port channel now i get, Error: Port is in Layer-2 mode Gi 2/36, still...

Trying to setup a port channel to connect a new switch with ports that were previously configured.. error

force10(conf-if-range-gi-2/36-37)#port-channel-protocol lacp % Error: Port is not in default mode. % Error: Port is not in default mode. force10(conf-if-range-gi-2/36-37)#show config ! interface GigabitEthernet 2/36 no ip address no shutdown ! interface GigabitEthernet 2/37 no ip address no...

Trying to setup a port channel to connect a new switch with ports that were previously configured.. error

i issued the no shutdown and then shutdown and then no shutdown again and then tried no switchport and it worked. but now when i try and issue port-channel-protocol lacp i get force10(conf-if-range-gi-2/36-37)#no switchport force10(conf-if-range-gi-2/36-37)#port-channel-protocol lacp...

Trying to setup a port channel to connect a new switch with ports that were previously configured.. error

I would try removing the ports from the port channel, then issue the lacp command. # interface Port-channel 102 # no channel-member GigabitEthernet 2/36-37 Then enter the interfaces and try to set them to lacp. # interface range GigabitEthernet 2/36-37 # port-channel-protocol lacp See if that...

Syba Dual LAN Ports 1000-Base T Gigabit Ethernet Card Realtek Chipset (SD-PEX24033) $17.99 sss eligible @ amazon

Syba Dual LAN Ports 1000-Base T Gigabit Ethernet Card Realtek Chipset (SD-PEX24033) [amazon.com] Realtek RTL8111 Chipset •Complies with PIC-e Revision 1.1 •1-lane (x1) PCI-e with Transfer Rate 2.5Gb/s Full Duplex Channel •A high Performance 1000Base-T Ethernet Controller Card •Backward Compatible to 10/100Base-T Networking •10/100/1000Mbps Data Rate Auto Negotiation Operation •Compatible to Existing CAT-5 UTP Cabling •Fully Compliant with IEEE 802.3, 802.3u, 802.3ab Attached Images ...

Input and output connectors for custom parts

Posted by Mikemk in General > Site Feedback And Feature Requests:Could the ability, when adding a custom, to specify connectors on it be implemented? For example, if I added http://www.newegg.com/Product/Product.aspx?Item=N82E16816124064, it would use 1 PCIe x2 slot, and provide 4 SATA III slots....

MacBook Core Duo: New hard drive input/output error

My old MacBook hard drive died and so I installed a WD 250GB 5400RPM SATA HD myself but when trying to erase it I get a input/output error and I cannot seem to partition it. When I try to reinstall my original Tiger OS X the 'select a destination' step is blank and there is nothing to select. I'm not worried about the old HD as I had mostly everything backed up - I just want to get this new HD up and running and get my MacBook fixed! I starting to go through cold turkey without it... please h...

WTS: 2xUSB CAR CHARGER(Input voltage: 12V ~ 40V DC )(Output voltage: 5V)

Main caracteristics ## Charge 2 USB peripherals to cigarette lighter ## Supports up to 5V, 1A and 2.1A ## Compatible with smartphone,tablet PC etc… Caracteristics ## Dual USB car cigarette lighter charger ##Input voltage: 12V ~ 40V DC ##Output voltage: 5V ##Supports 1A & 2.1A $15 ...

Design Apple Development Security Automobile Network Photography Health Money Travel Shopping Issues Operating systems Drivers Software Programming Tech Home Science Sport Solution